Single-Crystal Ferroelectric-Based (K,Na)NbO3 Microcuboid/CuO Nanodot Heterostructures with Enhanced Photo-Piezocatalytic Activity.

Developing single-crystal-based heterostructured ferroelectrics with high-performance photo-piezocatalytic activity is highly desirable to utilize large piezopotentials and more reactive charges that can trigger the desired redox reactions. To that end, a single-crystal-based (K,Na)NbO3 (KNN) microcuboid/CuO nanodot heterostructure with enhanced photo-piezocataytic activity, prepared using a facile strategy that leveraged the synergy between heterojunction formation and an intense single-crystal-based piezoelectric effect, is reported herein. The catalytic rhodamine B degrading activity of KNN/CuO is investigated under light irradiation, ultrasonication, or co-excitation with both stimulations. Compared to polycrystalline KNN powders and bare KNN single-crystals, single-crystal-based KNN/CuO exhibits a higher piezocurrent density and an optimal energy band structure, resulting in 5.23 and 2.37 times higher piezocatalytic degradation activities, respectively. Furthermore, the maximum photo-piezocatalytic rate constant (≈0.093 min-1 ) of KNN/CuO under 25 min ultrasonication and light irradiation is superior to that of other KNN-based catalysts, and 1.6 and 48.6 times higher than individual piezocatalytic and photocatalytic reaction rate constants, respectively. The excellent photo-piezocatalytic activity is attributed to the enhanced charge-carrier separation and proper alignment of band structure to the required redox levels by the appropriate p-n heterojunction and high piezoelectric potential. This report provides useful insight into the relationships between heterojunctions, piezoelectric responses, and catalytic mechanisms for single-crystal-based heterostructured catalysts.

Improved Energy Storage Density and Efficiency of Nd and Mn Co-Doped Ba0.7Sr0.3TiO3 Ceramic Capacitors Via Defect Dipole Engineering.

In this paper, we investigate the structural, microstructural, dielectric, and energy storage properties of Nd and Mn co-doped Ba0.7Sr0.3TiO3 [(Ba0.7Sr0.3)1-xNdxTi1-yMnyO3 (BSNTM) ceramics (x = 0, 0.005, and y = 0, 0.0025, 0.005, and 0.01)] via a defect dipole engineering method. The complex defect dipoles (MnTi"-VO∙∙)∙ and (MnTi"-VO∙∙) between acceptor ions and oxygen vacancies capture electrons, enhancing the breakdown electric field and energy storage performances. XRD, Raman, spectroscopy, XPS, and microscopic investigations of BSNTM ceramics revealed the formation of a tetragonal phase, oxygen vacancies, and a reduction in grain size with Mn dopant. The BSNTM ceramics with x = 0.005 and y = 0 exhibit a relative dielectric constant of 2058 and a loss tangent of 0.026 at 1 kHz. These values gradually decreased to 1876 and 0.019 for x = 0.005 and y = 0.01 due to the Mn2+ ions at the Ti4+- site, which facilitates the formation of oxygen vacancies, and prevents a decrease in Ti4+. In addition, the defect dipoles act as a driving force for depolarization to tailor the domain formation energy and domain wall energy, which provides a high difference between the maximum polarization of Pmax and remnant polarization of Pr (ΔP = 10.39 µC/cm2). Moreover, the complex defect dipoles with optimum oxygen vacancies in BSNTM ceramics can provide not only a high ΔP but also reduce grain size, which together improve the breakdown strength from 60.4 to 110.6 kV/cm, giving rise to a high energy storage density of 0.41 J/cm3 and high efficiency of 84.6% for x = 0.005 and y = 0.01. These findings demonstrate that defect dipole engineering is an effective method to enhance the energy storage performance of dielectrics for capacitor applications.

Direct Printing of Ultrathin Block Copolymer Film with Nano-in-Micro Pattern Structures.

Nanotransfer printing (nTP) is one of the most promising nanopatterning methods given that it can be used to produce nano-to-micro patterns effectively with functionalities for electronic device applications. However, the nTP process is hindered by several critical obstacles, such as sub-20 nm mold technology, reliable large-area replication, and uniform transfer-printing of functional materials. Here, for the first time, a dual nanopatterning process is demonstrated that creates periodic sub-20 nm structures on the eight-inch wafer by the transfer-printing of patterned ultra-thin (<50 nm) block copolymer (BCP) film onto desired substrates. This study shows how to transfer self-assembled BCP patterns from the Si mold onto rigid and/or flexible substrates through a nanopatterning method of thermally assisted nTP (T-nTP) and directed self-assembly (DSA) of Si-containing BCPs. In particular, the successful microscale patternization of well-ordered sub-20 nm SiOx patterns is systematically presented by controlling the self-assembly conditions of BCP and printing temperature. In addition, various complex pattern geometries of nano-in-micro structures are displayed over a large patterning area by T-nTP, such as angular line, wave line, ring, dot-in-hole, and dot-in-honeycomb structures. This advanced BCP-replicated nanopatterning technology is expected to be widely applicable to nanofabrication of nano-to-micro electronic devices with complex circuits.

Enhanced Energy Storage Performance and Efficiency in Bi0.5(Na0.8K0.2)0.5TiO3-Bi0.2Sr0.7TiO3 Relaxor Ferroelectric Ceramics via Domain Engineering.

Dielectric materials are highly desired for pulsed power capacitors due to their ultra-fast charge-discharge rate and excellent fatigue behavior. Nevertheless, the low energy storage density caused by the low breakdown strength has been the main challenge for practical applications. Herein, we report the electric energy storage properties of (1 - x) Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics that are enhanced via a domain engineering method. A rhombohedral-tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x = 0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward a high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie-Weiss law. The rhombohedral-tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high Pmax and low Pr, improving the breakdown strength with BST and resulting in a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

Giant Energy Density via Mechanically Tailored Relaxor Ferroelectric Behavior of PZT Thick Film.

Relaxor ferroelectrics (RFEs) are being actively investigated for energy-storage applications due to their large electric-field-induced polarization with slim hysteresis and fast energy charging-discharging capability. Here, a novel nanograin engineering approach based upon high kinetic energy deposition is reported, for mechanically inducing the RFE behavior in a normal ferroelectric Pb(Zr0.52 Ti0.48 )O3 (PZT), which results in simultaneous enhancement in the dielectric breakdown strength (EDBS ) and polarization. Mechanically transformed relaxor thick films with 4 µm thickness exhibit an exceptional EDBS of 540 MV m-1 and reduced hysteresis with large unsaturated polarization (103.6 µC cm-2 ), resulting in a record high energy-storage density of 124.1 J cm-3 and a power density of 64.5 MW cm-3 . This fundamental advancement is correlated with the generalized nanostructure design that comprises nanocrystalline phases embedded within the amorphous matrix. Microstructure-tailored ferroelectric behavior overcomes the limitations imposed by traditional compositional design methods and provides a feasible pathway for realization of high-performance energy-storage materials.

Intense Pulsed Light Thermal Treatment of Pb(Zr,Ti)O3 /Metglas Heterostructured Films Resulting in Extreme Magnetoelectric Coupling of over 20 V cm-1 Oe-1.

Magnetoelectric (ME) film composites consisting of piezoelectric and magnetostrictive materials are promising candidates for application in magnetic field sensors, energy harvesters, and ME antennas. Conventionally, high-temperature annealing is required to crystallize piezoelectric films, restricting the use of heat-sensitive magnetostrictive substrates that enhance ME coupling. Herein, a synergetic approach is demonstrated for fabricating ME film composites that combines aerosol deposition and instantaneous thermal treatment based on intense pulsed light (IPL) radiation to form piezoelectric Pb(Zr,Ti)O3 (PZT) thick films on an amorphous Metglas substrate. IPL rapidly anneals PZT films within a few milliseconds without damaging the underlying Metglas. To optimize the IPL irradiation conditions, the temperature distribution inside the PZT/Metglas film is determined using transient photothermal computational simulation. The PZT/Metglas films are annealed using different IPL pulse durations to determine the structure-property relationship. IPL treatment results in an enhanced crystallinity of the PZT, thus improving the dielectric, piezoelectric, and ME properties of the composite films. An ultrahigh off-resonance ME coupling (≈20 V cm-1  Oe-1 ) is obtained for the PZT/Metglas film that is IPL annealed at a pulse width of 0.75 ms (an order of magnitude higher than that reported for other ME films), confirming the potential for next-generation, miniaturized, and high-performance ME devices.

Magnetically Driven Powerless Lighting Device with Kirigami Structured Magneto-Mechanoluminescence Composite.

The energy crisis and global shift toward sustainability drive the need for sustainable technologies that utilize often-wasted forms of energy. A multipurpose lighting device with a simplistic design that does not need electricity sources or conversions can be one such futuristic device. This study investigates the novel concept of a powerless lighting device driven by stray magnetic fields induced by power infrastructure for obstruction warning light systems. The device consists of mechanoluminescence (ML) composites of a Kirigami-shaped polydimethylsiloxane (PDMS) elastomer, ZnS:Cu particles, and a magneto-mechano-vibration (MMV) cantilever beam. Finite element analysis and luminescence characterization of the Kirigami structured ML composites are discussed, including the stress-strain distribution map and comparisons between different Kirigami structures based on stretchability and ML characteristic trade-offs. By coupling a Kirigami-structured ML material and an MMV cantilever structure, a device that can generate visible light as luminescence from a magnetic field can be created. Significant factors that contribute to luminescence generation and intensity are identified and optimized. Furthermore, the feasibility of the device is demonstrated by placing it in a practical environment. This further proves the functionality of the device in harvesting weak magnetic fields into luminescence or light, without complicated electrical energy conversion steps.

Perovskite Piezoelectric-Based Flexible Energy Harvesters for Self-Powered Implantable and Wearable IoT Devices.

In the ongoing fourth industrial revolution, the internet of things (IoT) will play a crucial role in collecting and analyzing information related to human healthcare, public safety, environmental monitoring and home/industrial automation. Even though conventional batteries are widely used to operate IoT devices as a power source, these batteries have a drawback of limited capacity, which impedes broad commercialization of the IoT. In this regard, piezoelectric energy harvesting technology has attracted a great deal of attention because piezoelectric materials can convert electricity from mechanical and vibrational movements in the ambient environment. In particular, piezoelectric-based flexible energy harvesters can precisely harvest tiny mechanical movements of muscles and internal organs from the human body to produce electricity. These inherent properties of flexible piezoelectric harvesters make it possible to eliminate conventional batteries for lifetime extension of implantable and wearable IoTs. This paper describes the progress of piezoelectric perovskite material-based flexible energy harvesters for self-powered IoT devices for biomedical/wearable electronics over the last decade.

Molten-Salt Processed Potassium Sodium Niobate Single-Crystal Microcuboids with Dislocation-Induced Nanodomain Structures and Relaxor Ferroelectric Behavior.

We herein report a facile molten-salt synthetic strategy to prepare transparent and uniform Li, Ba-doped (K,Na)NbO3 (KNN) single-crystal microcuboids (∼80 µm). By controlling the degree of supersaturation, different growth modes were found and the single-crystal microcuboids were synthesized via island-like oriented attachment of KNN particles onto the growing surface. The distinct relaxor ferroelectric (RFE) properties were achieved in the single-crystal microcuboids, which were different from the normal ferroelectric (FE) properties found in their KNN ceramic counterparts prepared through a solid-state reaction using the same initial precursors. The RFE properties were realized by dislocation-induced nanodomain formation during oriented attachment growth of single-crystal microcuboids, which is different from the current strategies to derive the nanodomains by the local compositional inhomogeneity or the application of an electric field. The dislocations served as nucleation sites for ferroelectric domain walls and block the growth of domains. The KNN single-crystal microcuboids exhibited a higher effective piezoelectric coefficient (∼459 pm/V) compared to that of the bulk KNN ceramic counterpart (∼90 pm/V) and showed the broad diffuse maxima in the temperature dependence dielectric permittivity. The high maximum polarization (69.6 µC/cm2) at a relatively low electric field (30 kV/cm) was beneficial for energy storage applications. Furthermore, the KNN-based transparent, flexible pressure sensor directly monitored the mechanical motion of human activity without any external electric power. This study provides insights and synthetic strategies of single-crystal RFE microcuboids for other different perovskites, in which nanodomain structures are primarily imposed by their chemical composition.

Magneto-Mechano-Electric (MME) Composite Devices for Energy Harvesting and Magnetic Field Sensing Applications.

Magneto-mechano-electric (MME) composite devices have been used in energy harvesting and magnetic field sensing applications due to their advantages including their high-performance, simple structure, and stable properties. Recently developed MME devices can convert stray magnetic fields into electric signals, thus generating an output power of over 50 mW and detecting ultra-tiny magnetic fields below pT. These inherent outstanding properties of MME devices can enable the development of not only self-powered energy harvesters for internet of thing (IoT) systems but also ultra-sensitive magnetic field sensors for diagnosis of human bio-magnetism or others. This manuscript provides a brief overview of recently reported high-performance MME devices for energy harvesting and magnetic sensing applications.

Harvesting electrical energy using plasmon-enhanced light pressure in a platinum cut cone.

We have designed a method of harvesting electrical energy using plasmon-enhanced light pressure. A device was fabricated as a cut cone structure that optimizes light collection so that the weak incident light pressure can be sufficiently enhanced inside the cut cone to generate electrical energy. An increase in the device's current output is a strong indication that the pressure of incident light has been enhanced by the surface plasmons on a platinum layer inside the cut cone. The electrical energy harvested in a few minutes by irradiating pulsed laser light on a single micro device was possible to illuminate a blue LED.

Multiscale surface modified magneto-mechano-triboelectric nanogenerator enabled by eco-friendly NaCl imprinting stamp for self-powered IoT applications.

In this paper, we demonstrated a multiscale micro- and nano-structured magneto-mechano-triboelectric nanogenerator (MMTENG) enabled by a salt particle imprinting process to power an internet of thing (IoT) sensor. The fine salt particles were utilized to form a multiscale structure on a triboelectric polymer film by mechanical pressure via an eco-friendly, low-cost, and simple process, thereby reinforcing the contact triboelectrification and electrostatic induction. The surface modified MMTENG can generate an open-circuit peak-to-peak voltage of 851 V, a short-circuit current of 155 µA, and a maximum peak power of 10.3 mW under an AC magnetic field of 8 Oe. The energy device also presented output stability over 124 million operating cycles. Finally, the electricity of the surface enhanced MMTENG device was directly utilized to power an IoT temperature sensor with integration of an energy harvester, energy conversion circuit, and storage capacitor.

Enhancement of Energy-Harvesting Performance of Magneto-Mechano-Electric Generators through Optimization of the Interfacial Layer.

Among various energy harvester paradigms, the simple cantilever-structured magneto-mechano-electric (MME) energy generator comprises a piezoelectric material laminated on a magnetostrictive metal plate and permanent magnets as proof mass, exhibiting excellent magnetic energy-harvesting performance. The current challenge in using MME energy harvesters is the mechano-electric coupling at the interface between the piezoelectric material and magnetostrictive metal layer, which depends significantly on the mechanical properties of the interfacial adhesive layer. In this study, the effects of four types of adhesive interfacial layers on the output power and environmental and fatigue resistances of MME harvesters are systematically investigated. An optimized MME energy generator with an adhesive interfacial layer of 18.8 µm thickness and elastic modulus of 3.1 GPa achieves colossal enhancement (∼300%) with a maximum output power density of 0.92 mW/cm2, while a 10 Oe (=10 G = 1 mT in air; 60 Hz) magnetic field is applied. In addition, the generator exhibits a robust endurance of continuous 108 fatigue cycles and excellent temperature stability in the range of -30 to 70 °C. The presented MME generator, which harvests stray magnetic energy reliably, is promising as a low-cost and efficient autonomous power source for Internet of Things devices, wireless sensor networks, and so on.

Selective Phase Control of Dopant-Free Potassium Sodium Niobate Perovskites in Solution.

As one of the perovskite families, potassium sodium niobates (K1-xNax)NbO3 (KNN) have been gaining tremendous attention due to their various functional properties which can be largely determined by their crystallographic phase and composition. However, a selective evolution of different phases for KNN with controlled composition can be difficult to achieve, especially in solution chemical synthesis because of its strong tendency to stabilize into orthorhombic phase at conventional synthetic temperature. We herein developed a facile solution approach to control the phase and composition of dopant-free KNN particles selectively through the modification of reaction parameters. A conventional hydrothermal synthesis method yielded orthorhombic KNN particles, while the monoclinic phase, which has never been observed in a bulk counterpart, was kinetically generated by the compositional modification of an intermediate phase under a high-intensity ultrasound irradiation. Cubic KNN particles were stabilized when ethylene glycol was used as a co-solvent together with deionized water through bonding between ethylene glycol molecules and the surface of the KNN. Composite-structured piezoelectric harvesters were fabricated using each phase of KNN particles and the ß-phase poly(vinylidene fluoride-co-trifluoroethylene) polymer. Maximum output power was found for the harvester containing orthorhombic KNN particles. This facile synthetic methodology could pave a new pathway for fabricating numerous phase-controlled materials.

A Comparison Study of Fatigue Behavior of Hard and Soft Piezoelectric Single Crystal Macro-Fiber Composites for Vibration Energy Harvesting.

Designing a piezoelectric energy harvester (PEH) with high power density and high fatigue resistance is essential for the successful replacement of the currently using batteries in structural health monitoring (SHM) systems. Among the various designs, the PEH comprising of a cantilever structure as a passive layer and piezoelectric single crystal-based fiber composites (SFC) as an active layer showed excellent performance due to its high electromechanical properties and dynamic flexibilities that are suitable for low frequency vibrations. In the present study, an effort was made to investigate the reliable performance of hard and soft SFC based PEHs. The base acceleration of both PEHs is held at 7 m/s2 and the frequency of excitation is tuned to their resonant frequency (fr) and then the output power (Prms) is monitored for 107 fatigue cycles. The effect of fatigue cycles on the output voltage, vibration displacement, dielectric, and ferroelectric properties of PEHs was analyzed. It was noticed that fatigue-induced performance degradation is more prominent in soft SFC-based PEH (SS-PEH) than in hard SFC-based PEH (HS-PEH). The HS-PEH showed a slight degradation in the output power due to a shift in fr, however, no degradation in the maximum power was noticed, in fact, dielectric and ferroelectric properties were improved even after 107 vibration cycles. In this context, the present study provides a pathway to consider the fatigue life of piezoelectric material for the designing of PEH to be used at resonant conditions for long-term operation.

Enhancement of Magnetoelectric Conversion Achieved by Optimization of Interfacial Adhesion Layer in Laminate Composites.

We report the effect of epoxy adhesion layers with different mechanical or physical property on a magnetoelectric (ME) composite laminate composed of FeBSi alloy (Metglas)/single-crystal Pb(Mg1/3Nb2/3)O3-Pb(Zr,Ti)O3/Metglas to achieve an improved ME conversion performance. Through theoretical simulation, it was revealed that the Young's modulus and the thickness of interfacial adhesives were major parameters that influence the conversion efficiency in ME composites. In the experimental evaluation, we utilized three epoxy materials with a distinct Young's modulus and adjusted the average thickness of the adhesion layers to optimize the ME conversion. The experimental results show that a thin epoxy layer with a high Young's modulus provided the best performance in the inorganic-based ME conversion process. By tailoring the interfacial adhesion property, the ME laminate generated a high conversion coefficient of 328.8 V/(cm Oe), with a mechanical quality factor of 132.0 at the resonance mode. Moreover, we demonstrated a highly sensitive alternating current magnetic field sensor that had a detection resolution below 10 pT. The optimization of the epoxy layers in the ME laminate composite provided significant enhancement of the ME response in a simple manner.

Boosting the Recoverable Energy Density of Lead-Free Ferroelectric Ceramic Thick Films through Artificially Induced Quasi-Relaxor Behavior.

Dielectric ceramic film capacitors, which store energy in the form of electric polarization, are promising for miniature pulsed power electronic device applications. For a superior energy storage performance of the capacitors, large recoverable energy density, along with high efficiency, high power density, fast charge/discharge rate, and good thermal/fatigue stability, is desired. Herein, we present highly dense lead-free 0.942[Na0.535K0.480NbO3]-0.058LiNbO3 (KNNLN) ferroelectric ceramic thick films (∼5 µm) demonstrating remarkable energy storage performance. The nanocrystalline KNNLN thick film fabricated by aerosol deposition (AD) process and annealed at 600 °C displayed a quasi-relaxor ferroelectric behavior, which is in contrast to the typical ferroelectric nature of the KNNLN ceramic in its bulk form. The AD film exhibited a large recoverable energy density of 23.4 J/cm3, with an efficiency of over 70% under the electric field of 1400 kV/cm. Besides, an ultrahigh power density of 38.8 MW/cm3 together with a fast discharge speed of 0.45 µs, good fatigue endurance (up to 106 cycles), and thermal stability in a wide temperature range of 20-160 °C was also observed. Using the AD process, we could make a highly dense microstructure of the film containing nano-sized grains, which gave rise to the quasi-relaxor ferroelectric characteristics and the remarkable energy storage properties.

Laser Irradiation of Metal Oxide Films and Nanostructures: Applications and Advances.

Recent technological advances in developing a diverse range of lasers have opened new avenues in material processing. Laser processing of materials involves their exposure to rapid and localized energy, which creates conditions of electronic and thermodynamic nonequilibrium. The laser-induced heat can be localized in space and time, enabling excellent control over the manipulation of materials. Metal oxides are of significant interest for applications ranging from microelectronics to medicine. Numerous studies have investigated the synthesis, manipulation, and patterning of metal oxide films and nanostructures. Besides providing a brief overview on the principles governing the laser-material interactions, here, the ongoing efforts in laser irradiation of metal oxide films and nanostructures for a variety of applications are reviewed. Latest advances in laser-assisted processing of metal oxides are summarized.

Enhanced Self-Biased Magnetoelectric Coupling in Laser-Annealed Pb(Zr,Ti)O3 Thick Film Deposited on Ni Foil.

Enhanced and self-biased magnetoelectric (ME) coupling is demonstrated in a laminate heterostructure comprising 4 µm-thick Pb(Zr,Ti)O3 (PZT) film deposited on 50 µm-thick flexible nickel (Ni) foil. A unique fabrication approach, combining room temperature deposition of PZT film by granule spray in vacuum (GSV) process and localized thermal treatment of the film by laser radiation, is utilized. This approach addresses the challenges in integrating ceramic films on metal substrates, which is often limited by the interfacial chemical reactions occurring at high processing temperatures. Laser-induced crystallinity improvement in the PZT thick film led to enhanced dielectric, ferroelectric, and magnetoelectric properties of the PZT/Ni composite. A high self-biased ME response on the order of 3.15 V/cm·Oe was obtained from the laser-annealed PZT/Ni film heterostructure. This value corresponds to a ∼2000% increment from the ME response (0.16 V/cm·Oe) measured from the as-deposited PZT/Ni sample. This result is also one of the highest reported values among similar ME composite systems. The tunability of self-biased ME coupling in PZT/Ni composite has been found to be related to the demagnetization field in Ni, strain mismatch between PZT and Ni, and flexural moment of the laminate structure. The phase-field model provides quantitative insight into these factors and illustrates their contributions toward the observed self-biased ME response. The results present a viable pathway toward designing and integrating ME components for a new generation of miniaturized tunable electronic devices.

Flash-Induced Self-Limited Plasmonic Welding of Silver Nanowire Network for Transparent Flexible Energy Harvester.

The outstanding performance (sheet resistance of 5 Ω sq-1 at transmittance of 90%) and strongly adhesive (30.7 J m-2 ) silver nanowires (AgNWs) are fabricated using flash-induced plasmonic welding (FPW) based on theoretical research of photothermal interactions. The FPW-processed AgNWs are utilized as electrodes of a transparent flexible energy harvester, and this device exhibits excellent transmittance and high electric output performance. The FPW methodology provides a high-tech solution for transparent flexible electronics.